涂膠行業常用的幾種膠水！
有不同種類的膠水機經常使用膠水,可以說超過同類產品,每個模型都有不同的性能,膠水涂料常用的膠水,通道結束膠機可以使用,只能評論的一些比較常見的膠水,滿足一些基本的涂料行業,壓力桶的使用方法。
There are different types of glue machines often use glue, it can be said that more than similar products, each model has different performance, glue commonly used in glue coatings, channel end glue machine can be used, can only comment on some of the more common glue, to meet some basic paint industry, the use of pressure barrels.
一、常用膠水種類
Types of common glue
膠機常用的涂層膠分別用銀膠、紅膠、熱熔膠、硅膠、AB膠、快干膠、焊錫膏、環氧天然橡膠、填充底部的橡膠、乙烯基、厭氧膠、耐高溫膠、白膠等等,這些都是常用的涂層膠,膠與通道膠機可以使用,但需要更換一些配件,可以滿足生產的需要,上膠閥對上膠有幾種要求較高，類似于硅酮、熱熔膠、紅膠、厭氧膠等需要特殊的上膠閥設備才能達到真正上膠的末端要求。
The commonly used coating adhesives for rubber machines are silver glue, red glue, hot melt glue, silica gel, AB glue, quick-drying glue, solder paste, epoxy natural rubber, rubber filled with the bottom, vinyl, anaerobic glue, high temperature resistant glue, white glue, etc. These are commonly used coating adhesives. The glue and channel glue machine can be used, but some accessories need to be replaced. To meet the needs of production, there are several kinds of higher requirements for gluing valves. Similar to silicone, hot melt glue, red glue, anaerobic glue, special gluing valve equipment is needed to achieve the end requirements of real gluing.
其次，使用壓力桶要注意問題
Secondly, attention should be paid to the use of pressure barrels.
是否需要這些類型的膠水來填充壓力桶?對特定的需求,自動化生產是不需要通過更換可能每次膠,使用氣動式壓力桶來滿足通道膠機連續膠的要求,只有壓力桶必須注意使用方法,或特別容易出現膠水供應不足,導致沒有膠水,膠水使用膠水每個日出生產是非常大的。
Do you need these types of glue to fill pressure barrels? For specific requirements, automatic production does not need to replace each possible glue, using pneumatic pressure barrel to meet the requirements of continuous glue channel glue machine, only the pressure barrel must pay attention to the use of methods, or especially prone to glue shortage, resulting in no glue, glue to make. It is very big to produce glue every day.
三、澆注塑料桶的應用方法
3. Application Method of Casting Plastic Barrel
如何使用溝道澆注機的氣動壓力桶?相對短暫,要了解膠水的性質,然后觀察濃度條件下,特別容易冷凝式連續混合,避免冷凝,更高水平的膠是一樣的,有一個低降水的膠水,膠水濃度還需要添加混合,然后加入膠桶式氣壓,氣壓管、壓力釋放閥、防爆閥、等,密封,以避免泄漏,然后接軟管膠機、這樣的基本是有聯系的。先在壓力桶內滿壓后，再用槽口澆注機抽膠，以免導致膠水斷續。
How to use the pneumatic pressure barrel of the channel pouring machine? It is relatively short. First, we need to understand the nature of glue. Then, we should observe the concentration conditions, especially easy to condense continuous mixing, avoid condensation. Higher level glue is the same. There is a low-precipitation glue, the glue concentration also needs to be mixed, and then add the barrel pressure, barometric pipe, etc. Pressure release valves, explosion-proof valves, etc., are sealed to avoid leakage, and then hose glue machine, which is basically related. After full pressure in the pressure barrel, the glue is drawn by the groove pouring machine to avoid intermittent glue.
上一篇：中空玻璃打膠機手工刮膠怎么操作？
下一篇：雙組份結構膠混合不均勻怎么辦？
