蜜桃av噜噜一区二区三区-蜜桃av麻豆av果冻传媒-蜜桃av亚洲精品一区二区-蜜桃bt天堂精品视频在线观看-蜜桃成人无码区免费视频网站-蜜桃福利视频

你現在的位置:首頁>企業動態

中空玻璃打膠機斷膠解決方法!

瀏覽:0
  中空玻璃打膠機斷膠解決方法:
  Solution to broken glue of hollow glass dispenser:
  要進行 中空玻璃打膠機排除問題,然后針對性解決斷膠的問題。
  The first choice is to eliminate the problem of hollow glass gluing machine, and then solve the problem of glue breaking.
  作為中空玻璃制作設備的 中空玻璃打膠機中丁基膠涂布機,在使用中會因為一點小問題影響使用,比如更常見的:
  As a hollow glass production equipment, the butyl glue coating machine in the hollow glass gluing machine will affect the use due to a small problem, such as the most common:
    中空玻璃打膠機為了增加制作效率調整是輸送帶速度很快,出膠量沒法調整,導致斷斷續續的原因之一。
  In order to increase the production efficiency, the adjustment of the first hollow glass gluing machine is one of the reasons that the speed of the conveyor belt is very fast, and the glue output cannot be adjusted, resulting in intermittent.
  第二  對于膠缸和膠頭的溫度沒有設置好,到時有的膠沒有達到應有的溫度,導致出現鋸齒類的情況。
  Second, the temperature of the rubber cylinder and the rubber head is not set properly, and some rubber fails to reach the proper temperature at that time, resulting in sawtooth.
  第三  中空玻璃打膠機建議把溫度調整到合適的溫度,使丁基膠化掉,這樣幾乎不會出現以上問題。
  The third insulating glass gluing machine suggested that the temperature should be adjusted to a suitable temperature to make butyl gel off, so that the above problems would hardly occur.
濟南雙組份打膠機
  第四  如果是從中空玻璃打膠機剛開始使用到現在一直是這種情況 膠頭出膠口有毛刺 膠頭一般有兩種 膠口處有槽和無槽兩種
  Fourth, if it's from the beginning of using the hollow glass dispenser to now, it's always the case that the rubber head has burr at the rubber outlet, and there are generally two types of rubber head: grooved and grooveless
  第五  換膠以后出現這種情況 溫度到達上限以后 出膠不正常 膠口處膠沒有完全融化 手動排出一部分膠 也就是打幾個框子 將壓力調大 多打幾個框子 將膠缸內的膠擠實。
  After the fifth rubber change, when the temperature reaches the upper limit, the glue at the abnormal rubber outlet does not melt completely, and part of the glue is discharged manually, that is to say, several frames are set to adjust the pressure, mostly several frames are set to compact the glue in the rubber cylinder.
  第六 雙組份打膠機采購的丁基膠質量差,配置成本低,雜質堵塞引起的。
  The quality of butyl rubber purchased by the sixth two-component beater is poor, the configuration cost is low, and the impurities are blocked.
  第七  放膠后沒有進行放氣。
  After the seventh dispensing, there was no bleeding.

上一篇:高速點膠機的產品特點以及使用方法!
下一篇:中空玻璃打膠機生產效率高不高?

  • 微信
主站蜘蛛池模板: 日本高清一级做a爱过程免费视频 | 国产成人高清亚洲一区91 | 神马九九 | 国产99久久久久久免费看 | 亚州激情视频在线播放 | 在线 | 一区二区三区四区 | 一区二区三区四区在线视频 | 国产三级日产三级日本三级 | 天天弄 | 亚洲欧美日韩国产专区一区 | 狠狠综合久久久久综合 | 国产小视频免费在线观看 | 成人欧美 | 99激情网 | 99这里只有精品66视频 | 奇米影视第四色在线 | 精品久久伦理中文字幕 | 久久精品国产亚洲a | 四房激情 | 四虎伦理| 国产精品真实对白精彩久久 | 美女又黄又免费的视频 | 日本欧美另类 | 另类欧美chinese | 成人永久免费视频网站在线观看 | 午夜三级做爰视频在线看 | 国产精品u任我爽爆在线播放 | 亚洲国产欧美视频 | 中文字幕一区日韩在线视频 | 3级毛片| 看免费5xxaaa| 亚洲日本人成网站在线观看 | 亚洲天堂爱爱 | 亚洲一区免费看 | 国产a毛片高清视 | 久久影视免费体验区午夜啪啪 | 波多野结衣一区二区三区高清在线 | 97最新网址| 免费精品国产 | 91在线短视频 | 99久久精品免费看国产麻豆 |