蜜桃av噜噜一区二区三区-蜜桃av麻豆av果冻传媒-蜜桃av亚洲精品一区二区-蜜桃bt天堂精品视频在线观看-蜜桃成人无码区免费视频网站-蜜桃福利视频

你現在的位置:首頁>企業動態

濟南雙組份打膠機介紹安裝的順序是怎樣的?

瀏覽:0
1、雙組份打膠機設備應安裝在干燥、無粉塵、無腐蝕性氣體的壞境中(該要求與其他設備一致,當然如果條件達不到少爭取無腐蝕性氣體,畢竟設備中有電線以及管路這些配件抗腐蝕性不高)。
1. The equipment of two-component gluing machine should be installed in a dry, dust-free and non corrosive environment (the requirement is consistent with other equipment. Of course, if the conditions are not met, at least strive for non corrosive gas. After all, there are wires and pipelines in the equipment, and the corrosion resistance of these accessories is not high).
2、室內溫度更好控制在10~40度的室內堅硬地面上,地面應水平度要好。(小編這里說的地面水平度要好不一定要非常的平整才行,我們的設備在設計之初已經考慮到了地面復雜性的因素所以對地面平整度是有相當大的忍讓度的,只要不是幅度提別的大一般都可以正常工作。)
2. The indoor temperature should be controlled on the indoor hard ground of 10-40 degrees, and the ground should be level. (Xiaobian here says that the level of the ground must be very flat. At the beginning of the design, our equipment has considered the factors of the complexity of the ground, so it has a great tolerance to the level of the ground. As long as the range is not raised, it can work normally.)
3、雙組份打膠機安裝之前,應先檢查是否有因運輸、搬動造成的變形、損壞和緊固件松動情況,之前就曾經有客戶在移動打膠機的過程中把設備的智能控制系統的一個零部件碰掉了而導致設備無法正常運行,我們的工作人員到現場后才排查出的原因。
3. Before the installation of the two-component dispenser, we should first check whether there is deformation, damage and fastener loosening caused by transportation and moving. Before that, a customer knocked off a part of the intelligent control system of the equipment in the process of moving the dispenser, which led to the normal operation of the equipment. Our staff found out the cause after arriving at the site.
4、我們可以根據地面平整度的實際情況來通過調整設備的可升降地腳螺栓來調整設備的水平度直到設備水平而穩固。然后按圖接線并可靠接地,把氣源接入機器所配帶的氣源接口,確保無漏氣現象。
4. First of all, we can adjust the levelness of the equipment by adjusting the lifting anchor bolts of the equipment according to the actual situation of the ground flatness until the equipment is level and stable. Then according to the diagram wiring and reliable grounding, connect the air source to the air source interface of the machine to ensure no air leakage.
5、向油槽中加注液壓油指定位置,46#液壓油(約為50升左右)。
5. Fill the oil tank with hydraulic oil to the designated position, 46 ? hydraulic oil (about 50 liters).
6、接通電源并打開查看設備是否能夠正常運行。
6. Turn on the power and turn it on to see if the device is working properly.

上一篇:雙組份打膠機是否可以打三層中空玻璃!
下一篇:打膠機的調試工作應該怎么做?

  • 微信
主站蜘蛛池模板: 亚洲综合色丁香麻豆 | 情欲综合网 | 99国产福利视频在线观看 | 国产精品久久久尹人香蕉 | 欧美va亚洲va在线观看蝴蝶网 | 日日摸夜夜摸狠狠摸日日碰夜夜做 | 涩涩精品| 国产成人理在线观看视频 | 黄片一级毛片 | 久久99中文字幕 | 看全色黄大色大片免费视频 | sss欧美华人整片在线观看 | 国产四虎精品 | 国产成人亚洲精品老王 | 特级一级黄色片 | 久久永久免费 | 久久综合九色综合97婷婷女人 | 四虎永久免费网站入口2020 | 国产aaaaaaa毛片 | 国产精品在线 | 久久影视一区 | 日韩精品在线视频观看 | 天天操比| 国产极品白嫩美女在线观看看 | 奇米麻豆 | 国产一区二区三区在线观看精品 | 日本一级在线观看 | 波多野吉衣一区二区三区在线观看 | 天天摸天天操天天射 | 欧美在线一级精品 | 一级毛片免费观看不收费 | 天天操天天干天天操 | 九九热精彩视频 | 国产农村一一级特黄毛片 | 亚洲国产精品一区二区三区 | 99在线视频观看 | 国内精品久久久久影院嫩草 | 在线 中文字幕 日韩 欧美 | 亚洲国产成人久久笫一页 | 美女视频91| 夜夜天天操|