蜜桃av噜噜一区二区三区-蜜桃av麻豆av果冻传媒-蜜桃av亚洲精品一区二区-蜜桃bt天堂精品视频在线观看-蜜桃成人无码区免费视频网站-蜜桃福利视频

你現在的位置:首頁>企業動態

雙組份打膠機的注意事項

瀏覽:0
1.因為雙組份密封膠的固化需求一定時刻,因此 雙組份打膠機,已涂了雙組份密封膠的玻璃應水平輕輕搬動。
1. Because the solidification of the two-component sealant requires a certain time, the glass coated with the two-component sealant should be moved gently and horizontally.
2.A組、B組份膠應堅持清潔,嚴防異物進入膠中。
Group 2.A and B components should be kept clean and strictly prevented from entering the glue.
3.在接連作業過程中,膠槍每次中止作業時刻一般不得超越20分鐘,不然,運用A組份膠沖出悉數混合膠,直單一的A組份膠從槍口排出停止。
3. In the process of continuous operation, the gun should not stop operation more than 20 minutes each time. Otherwise, use component A glue to punch out all the mixed glue until a single component A glue is discharged from the muzzle to stop.
4.高壓膠管不得強行揉捏、曲折,避免影響體系正常作業。
4. high pressure hose should not be forced to knead, twists and turns, to avoid affecting the normal operation of the system.
雙組份打膠機
5.混膠器應常常堅持疏通,以確保杰出的出膠作用。如遇阻塞狀況,可用丙酮浸泡后清洗。主張每5組清洗一次。
5. rubber mixer should be constantly dredged to ensure excellent glue production. In case of obstruction, acetone can be soaked and cleaned. It is advocated that every 5 groups be cleaned once.
6.當膠槍長時刻不用時(超越一周),應拆下槍體運用溶劑將膠槍和混膠器內的殘留膠體清洗潔凈。
6. When the gun length is not used at all times (more than a week), the gun should be removed and the residual colloid in the gun and mixer should be cleaned by solvent.
7.不同雙組份膠出產廠家所出產的膠內含雜質數量不同,依據實際狀況明晰B組分的過濾網及單向止回閥,主張每兩組清洗一次。
7. Different two-component glue manufacturer produces different amount of impurities in the glue, according to the actual situation clear B component filter screen and one-way check valve, advocate cleaning every two groups.
8.任何因膠體固化所造成的膠槍、管路或整機的毛病 雙組份打膠機,一概不在保修規模之內。
8. Any defect caused by gel solidification in the rubber gun, pipeline or the whole machine, how much is the two-component glue beater, is not within the scope of warranty.
9.定時給各泵的加油口加油 中空雙組份打膠機,應確保油霧器內不斷油。
9. regularly fill the filling ports of each pump with a hollow two component glue machine, and ensure that the oil mist is constantly oil.
雙組份打膠機的結構原理:
The structure principle of two component rubber beating machine:
雙組份涂膠機由A、B膠泵、氣動體系、升降組織、機架等組成。現別離介紹如下:
The two component glue dispenser is composed of A, B glue pump, pneumatic system, lifting structure, rack and so on. The following are the following:
1.膠泵:
1. glue pump:
(1)A、B組份各設一個膠泵,在各自的氣馬達驅動下,別離作往復運動,將膠吸入并壓出。A、B膠泵別離與壓膠盤固定在一起,再與機架銜接組成各自的體系。
(1) Components A and B are equipped with a rubber pump, driven by their respective gas motors, separately reciprocating movement, will be glue inhalation and pressure out. The A and B rubber pumps are separated from the pressure plate and connected to the rack to form their own system.
(2)A、B組份的配比是經過份額杠桿進行調理:向里調理,B出膠量削減,向外調理,B出膠量添加。經過調理份額杠桿來操控B膠的出膠量,從而操控A、B膠的配比。
(2) The proportion of A and B components is regulated by share lever: inward conditioning, B glue reduction, outward conditioning, B glue added. After adjusting the share lever to control the gel output of B glue, the ratio of A and B glue is controlled.
(3)出膠量:由氣源處理器操控,逆時針調理,出膠量添加,順時針調理出膠量減小。(這兒指總出膠量) 本膠泵經過份額杠桿調理A、B膠量配比,具有操作靈敏,功能安穩,調理規模大等特點。
(3) glue yield: controlled by air source processor, counterclockwise conditioning, glue yield added, clockwise conditioning glue yield decreased. (hereinafter referred to as the total amount of glue) the rubber pump through the share of lever adjustment A, B glue ratio, with a sensitive operation, stable function, large-scale conditioning and other characteristics.
2 . 升降組織:
2. lifting organization:
A、B組份膠泵別離設一套氣動升降組織,該升降組織別離由兩個氣缸并聯組成,并經過橫梁固定銜接各自的泵體。其意圖之一是將兩缸的作用力經過壓盤作用在膠面上,壓力巨細由調壓閥調理,一般調整在0.3MPa左右;
Component A and B rubber pumps are separated by a set of pneumatic lifting organizations, which are composed of two cylinders in parallel, and connected with each other through a fixed beam. One of its intentions is to force the two cylinders on the glue surface through the pressure plate, the pressure is regulated by the pressure regulating valve, generally adjusted to about 0.3 MPa;
其二,當需求替換膠桶時,氣缸可將壓盤提起。離開膠桶,以便替換新的膠桶。
Second, when the need to replace the plastic bucket, the cylinder can lift the pressure plate. Leave the plastic bucket to replace the new plastic bucket.

上一篇:雙組份打膠機的使用安裝步驟
下一篇:中空玻璃打膠機在操作時要注意什么?

  • 微信
主站蜘蛛池模板: 国产亚洲精品久久久久久无 | 91热久久免费频精品黑人99 | 五月婷中文字幕 | 加勒比色综合 | 狠狠久久久久久亚洲综合网 | 日本aaaa级毛片在线看 | 日本大片久久久高清免费看 | 午夜99| 国产精品夜夜春夜夜爽久久 | 国产成人aa免费视频 | 亚洲欧美另类久久久精品能播放的 | 精品久久综合一区二区 | 日本不卡一区二区 | 久久九九精品一区二区 | 日韩精品影视 | 成人淫片免费视频95视频 | 欧美videos肥婆hd | 波多野结衣与公中出中文字幕 | 亚洲 中文 欧美 日韩 在线人 | 日本一级在线播放线观看视频 | 4虎影院午夜在线观看 | 伊人色综合久久天天网蜜月 | 日本不卡视频在线播放 | 国产成人精品免费视 | 91色综合综合热五月激情 | 日韩欧美一二三区 | 久久久久国产 | 一级肉体毛片视频免费看看 | 老司机免费福利影院 | 特级一级毛片视频免费观看 | 国产羞羞视频 | 99久久999久久久综合精品涩 | 另类最猛性xxxxx | 欧美日韩综合在线视频免费看 | 欧美日韩黄色 | 欧美一区二区视频 | 99久久综合狠狠综合久久aⅴ | 久久国产免费 | 99热这里只有精品在线 | 最新久久精品 | 91精东果冻蜜桃星空麻豆 |